
Spare Parts Inventory: What to Stock and How Much
A good spare parts inventory holds the parts whose failure would stop your equipment, in quantities your lead times justify, and nothing much beyond that. Get the list right, rank parts by criticality, set reorder points from real lead times, and review the whole thing on a schedule. The sections below walk through each step for workshops, fleets, marinas, farms and plants running engines and generators.
TL;DR
- Spare parts inventory is the stock of replacement components you keep to maintain, repair or restore equipment. The goal is less downtime without tying up cash in shelves of idle parts.
- Start with an accurate parts list tied to each machine. Without it, you cannot tell what is critical, what is duplicated and what is obsolete.
- Stock by criticality and lead time: hold long-lead parts for machines that would stop work, and order quick-to-source parts for low-risk machines when needed.
- Set a reorder point, a safety stock and a maximum for each stocked item, then review them monthly or quarterly.
- Track actual supplier lead times, not the quoted ones, and plan critical repairs around the worst recent case.
Table of Contents
- What a spare parts inventory is and why it matters
- Build the parts list before you touch stock levels
- Decide which parts are critical
- Set stock levels: reorder point, safety stock and maximum
- Plan for lead times, long and uncertain
- Our perspective
- Reduce excess, obsolete and duplicate stock
- Where Iberspares fits in your parts strategy
- Monitor and improve the program over time
- FAQ
- Sources
What a spare parts inventory is and why it matters
Spare parts inventory means the replacement components you keep on hand to maintain, repair or restore equipment that supports production. NetSuite’s overview frames the job as preventing downtime while avoiding overstock. Those are two opposing pressures, and most of the craft is in balancing them.
An academic literature review in the journal Sustainability describes spare parts as stock items used in maintenance to keep equipment in operating condition, and says managing them well reduces downtime and extends product lifetime. The same review estimates that the spare parts a machine with a lifetime of around 30 years consumes each year amount to nearly 2.5% of its original purchase price. Over a decade, that is a real budget line, which is why it deserves a method rather than guesswork.
For a diesel engine workshop, a marine maintenance company or a generator service team, the practical question is simple. When this engine fails on a Tuesday, will the part be on your shelf, on a truck by tomorrow, or three weeks away?
Three kinds of stock worth separating
Most operations mix these together and then wonder why the numbers do not make sense:
- Routine consumables: filters, belts, gaskets, seals, injectors, impellers. They are replaced on a schedule, move often and are cheap to hold.
- Wear and repair parts: water pumps, starter motors, turbo components, hydraulic fittings. They fail unpredictably, cost more and move slowly.
- Critical and long-lead items: major engine components or assemblies whose failure stops the machine and whose replacement takes weeks.
Each group gets a different stocking rule, which the later sections cover.
Build the parts list before you touch stock levels
You cannot manage what you cannot identify. The most common reason maintenance teams end up with the wrong parts on the shelf is a weak parts list: vague descriptions, no link to the machine, and the same item stored under two part numbers.
What each line should contain
One published specification for spare parts lists, KZR-DOC-04, sets a useful standard: each line should carry enough data for a buyer, storekeeper, engineer or planner to identify the correct part without calling the designer. It groups that data into four things:
- Asset reference: which machine or system the part belongs to, and where it is installed.
- Technical identity: the part number, description and specification.
- Supply identity: how it can be bought or verified later, including the manufacturer’s number.
- Maintenance logic: why it matters and when it is expected to be replaced.
For engine and equipment fleets, the practical translation is to record the engine model and serial number, the application (a marine auxiliary is not a generator set, even when the block is similar) and the exact part number from the manufacturer’s catalog. Application matters because the same engine family is often fitted with different components depending on the machine it powers.
Bills of materials come first for critical equipment
A bill of materials (BOM) lists every component of a machine. A Swain Smith guide to BOMs states that store-stocking and critical spare identification require complete, accurate and current BOMs, and that at minimum all critical facility equipment should have one. You do not need a BOM for every pump in the yard on day one. Start with the machines that stop revenue when they stop.
Standardize names, label bins, map locations
A guide to MRO storeroom management from Verdantis recommends a standard taxonomy, one unique record per item in your maintenance or ERP system, and standardized descriptions so you do not get duplicate or ambiguous entries. It also recommends labeling bins with part number, description and bin code, assigning unique location codes in the system, and checking physical labels against system records. None of this is glamorous. All of it saves the twenty minutes a technician otherwise spends looking for a fuel filter that is in the system but not on the shelf.
If you manage master data across many sites, ISO 14224-based master data practice points the same direction: naming conventions and allowable values, an equipment hierarchy, standardized spare parts lists, detailed BOMs, then integration into your maintenance system.
Decide which parts are critical
Stocking everything is expensive and stocking nothing is a gamble. Criticality is the filter between the two.
Fabrico’s maintenance guide calls asset criticality the single most useful input for what to stock. Parts for critical assets, especially long-lead parts whose failure would stop production, are the ones to hold. Parts for low-criticality, redundant or quickly sourced assets can be ordered when needed.
A simple three-question test
For each part on a machine, ask:
- What happens if it fails? Does the machine stop, run derated, or keep working?
- How long to replace it? Can you get it in a day, or is it a multi-week wait?
- What does holding it cost? Part price, shelf space, and the risk it never gets used.
A part that stops the machine and takes weeks to arrive is a stock item. A part that is cheap, quick to source and on a redundant machine is an order-when-needed item. Everything in between is a judgment call you make with usage history.
The cost-benefit logic
The Electric Power Research Institute’s work on critical spares is blunt about the difficulty: critical engineered items often have very long lead times and high costs, and covering every contingency drives up inventory value and carrying costs. A Dutch academic study on initial spare parts inventories puts the rule plainly: stock an item only if the benefit of having it immediately available outweighs the cost of holding it. It also notes that decisions on slow-moving parts matter most because wrong calls last a long time. The same study describes a classic decision rule built on four variables: consumption rate, price, lead time and the penalty cost of a stockout. Suppliers typically provide the first three, and you supply the last one, because only you know what an hour of downtime costs.

Safety-critical equipment at sea
Marine operators have a formal version of this. The OCIMF guidance on safety critical equipment and spare parts defines safety critical spare parts as components tied to the maintenance and repair of safety critical equipment. It recommends a proactive, risk-based approach to identify, document and maintain them, and says to evaluate each piece of equipment and its maintenance schedule to decide which spares and quantities to carry on board. Even if you run a small commercial fishing boat or a marina workboat rather than a tanker, the logic carries over: the engine that gets you home is a safety item.
Set stock levels: reorder point, safety stock and maximum
Once you know what to stock, set three numbers for each item. Fabrico describes them as follows:
| Setting | What it does | How to think about it |
|---|---|---|
| Reorder point | The level at which you place an order so stock lasts through the supplier’s lead time | Average usage during lead time, plus a buffer |
| Minimum or safety stock | A buffer against late deliveries and demand spikes | Raise it when lead times are long or unreliable, or the part is more critical |
| Maximum | A cap that stops over-ordering and dead stock | Keep it low for slow movers and expensive parts |
The same guide states that longer or less reliable lead times, and higher criticality, call for higher safety stock. That is the whole logic in one sentence.
A worked example
Suppose a workshop services compact excavators and uses about two fuel filter sets a month for one model. Lead time from the supplier is one week. Usage during lead time is roughly half a set, so a reorder point of one set plus a buffer of one more is sensible: order when you are down to three. For a high-value turbocharger used twice a year with a four-week lead time, you might hold one unit only if a machine stopped for weeks would cost more than the part sits idle. These numbers are illustrations, not rules. Use your own usage history and downtime cost.

Let software remind you, but keep the discipline
NetSuite notes that reorder-point reminders in inventory software can notify staff or trigger new orders when stock dips below the threshold. A spreadsheet works for a small shop. What matters is that someone owns the reorder point and checks it.
Check the shelf, not just the system
The OCIMF guidance says inventory procedures should include periodic inspection and stock-checking, and should address shelf life, preservation and safe storage, programming and update needs for electronic spares, and replenishment lead times. Rubber seals, hoses, batteries, electronic control units and anything with a shelf life belong on a rotation schedule. Spares are often needed most urgently in the condition they were bought in, and that depends on how they were stored.
Plan for lead times, long and uncertain
Lead time is the number that quietly decides how much stock you need. A Dutch academic framework for maintenance spare parts planning explains that supply lead time is the sum of several pieces: repair or supplier lead time, procurement time, picking, transport and storage time, and, for repairable parts, the time to hand in the failed unit. Any piece can slip, so the real timing shifts.
What to do about it
- Record promised versus actual delivery dates for every order. After a few months you have your real lead time per supplier and per part.
- Plan critical repairs around the worst recent case, not the quote.
- Agree contractual lead times with suppliers. The same framework notes that planned lead times for external supply are justified by contractual agreements, and that you should generally avoid asking suppliers to deliver early or late relative to them, so service levels are not jeopardized.
- Hold long-lead parts centrally when you run several sites. The OCIMF guidance suggests that some long-lead spares may be held centrally so dispatch can be prompt, and notes that fleets may keep larger components in a central shore-based warehouse. A multi-site rental company or a logistics fleet can use the same idea with a central parts room.
- Use a supplier with stock on the shelf for the parts you cannot justify carrying yourself. A distributor holding the parts you rarely need effectively becomes part of your inventory.
We think about inventory as a shared problem. The parts you cannot afford to hold should be one fast order away.
Our perspective
Most customers who call us in a hurry are not short of money. They are short of the right part number.
A Yanmar engine on a generator set, a marine auxiliary and a compact excavator can share a family name and still use different components. That is why we focus on application-specific knowledge of Yanmar and Sensei products. Identifying the correct part for the actual machine is where delays and wrong orders start, and where we aim to take them out.
We also keep an extensive in-stock inventory so that parts can be dispatched quickly. For a workshop or fleet owner, that changes the stocking math. You can hold your own critical spares for the machines that cannot stop, and rely on a distributor with deep stock for the long tail of parts you use rarely. Less cash sits on your shelf, and the emergency order still arrives fast.
Our advice is to write your parts list by machine, application and engine serial number, keep the manufacturer’s part number on every line, and keep a source ready for routine and emergency orders alike.
Duarte
Reduce excess, obsolete and duplicate stock
The opposite problem to a stockout is a shelf full of parts nobody will use. Verdantis reports that 10 to 25% of spare parts inventory may be obsolete or excess in mature industrial operations. Its recommended routine is monthly or quarterly reviews of non-moving items, a mandatory parts review whenever equipment is retired, and an annual obsolescence audit with disposal targets.
Your BOMs help here as well. The Swain Smith guide states that complete BOMs are needed for the annual obsolescence review, and that stock items not on any BOM are candidates for disposal, with exceptions for free-issue goods and consumables.
Cut duplicates and standardize
The same Verdantis guide describes reducing the number of distinct part numbers as one of the most effective cost-reduction strategies, often yielding 10 to 20% inventory reduction without changing service levels. That is a vendor’s claim, so treat the percentage as a possibility rather than a promise. The method is sound: audit for the same part held under different numbers, and build an interchangeability list so one item can serve several machines where the manufacturer allows it.
When you retire or sell a machine
This is the moment most shops forget. The machine leaves, the parts stay. Add “review dedicated spares” to your disposal checklist, and either transfer the stock to a sister machine, sell it, or write it off on purpose rather than by accident.
Where Iberspares fits in your parts strategy
If your fleet or customer base runs Yanmar or Sensei engines and equipment, we supply parts for construction and industry, agriculture, marine, power and generators, material handling and compact equipment. Our team identifies the correct application-specific component, so your parts list and your orders match the machine in front of you. Browse the catalog at Iberspares genuine Yanmar and Sensei parts and keep it in your supplier list for both routine and emergency orders.

We sell online to professional buyers: repair workshops, maintenance companies, equipment dealers and fleet operators. Have the engine model, serial number and the part number ready, and the order goes faster.
Monitor and improve the program over time
A spare parts inventory is never finished. Machines age, fleets change and suppliers shift. Treat it as a cycle: review, adjust, repeat.
Measure a few things
- Fill rate: the share of parts requests you could fill from stock.
- Stockouts on critical items: ideally none, and each one investigated.
- Excess and slow-moving value: how much cash is sitting in items with no recent use.
- Lead time performance: promised versus actual, by supplier.
A 2026 study in the SITEKNIK journal reports that a pilot using FSN analysis (ranking parts as fast, slow or non-moving) with a periodic review system lifted fill rate from 60% to 99%, above a 70% target. Its dashboard displayed stock status, fill rate, safety stock and reorder warnings. It is one pilot in Indonesia, not a guarantee, but it shows what a disciplined review can do.
A realistic review calendar
| Frequency | Task |
|---|---|
| Weekly | Check items below reorder point; log promised and actual delivery dates |
| Monthly | Review lead-time log; adjust safety stock where suppliers run late |
| Quarterly | Review non-moving items; check labels and bins against system records |
| Annually | Obsolescence audit; revisit criticality rankings and BOMs |
The Dutch planning framework suggests organizing spare parts decisions in a hierarchy, with decisions broken down and interfaces described, to improve efficiency, consistency and sustainability. For a small shop, that simply means deciding who owns each decision: who ranks criticality, who sets stock levels, who places orders.
FAQ
How much spare parts inventory should I keep?
Hold enough to cover the lead time of each part plus a safety buffer, and weight it by criticality. Parts for machines that would stop work and that take weeks to arrive deserve stock. Quick-to-source parts for low-risk machines can be ordered when needed. Use your own usage history and the cost of an hour of downtime to set the numbers.
What is the difference between safety stock and a reorder point?
The reorder point is the stock level at which you place an order so you do not run out while waiting for delivery. Safety stock is the extra buffer that protects you when delivery is late or demand spikes. Longer or less reliable lead times and higher criticality both call for more safety stock.
How do I know which spare parts are critical?
Start with the machines whose downtime costs you most, then list the parts whose failure would stop them. Rank those by how long replacement takes and what they cost to hold. Parts that stop the machine and take a long time to source are your critical spares. For marine and safety equipment, follow the risk-based approach in OCIMF guidance.
How often should I review my spare parts stock?
Check reorder points weekly, review lead times monthly, and review slow and non-moving items monthly or quarterly. Run a full obsolescence audit once a year, and review dedicated spares whenever you retire or sell a machine.
How do I reduce the risk of ordering the wrong part?
Keep the engine model, serial number, application and manufacturer’s part number on every line of your parts list. Verify against the manufacturer’s catalog before ordering. Supplier knowledge of the specific application helps, which is why we focus on Yanmar and Sensei applications.
Sources
- NetSuite: What Is Spare Parts Inventory Management?
- Spare Parts Inventory Management: A Literature Review (MDPI, Sustainability)
- Spare Parts List specification KZR-DOC-04
- Bills of Materials (Swain Smith)
- Step-by-Step Guide to Effective MRO Storeroom Management (Verdantis)
- Applying ISO 14224 for Master Data (Spartakus)
- Spare Parts Inventory Management for Maintenance Teams (Fabrico)
- Plant Support Engineering: Critical Spares (EPRI)
- Optimise initial spare parts inventories (Erasmus University Rotterdam)
- Safety Critical Equipment and Spare Parts Guidance (OCIMF)
- Maintenance spare parts planning and control: a framework for control and agenda for future research (TU Eindhoven)
- Spare Parts Inventory Management (Verdantis)
- Implementation of FSN Analysis and Periodic Review System (SITEKNIK)
Content strategy and optimisation for Google and AI-powered search platforms by Velveteen SaaS — specialists in online visibility and customer acquisition.